Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
What're your insights and beliefs on Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't exactly brain surgery, but it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is easily accessible, the job can relocate easily; if you have to open a wall surface to get rid of the old tub as well as place the brand-new bathtub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task and also fit attempting it. Instead of employing a service provider to take over a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you may need an expert plumber to make tube links.
This write-up will certainly help you install a new bathtub in your restroom if you have already bought a new tub and don't need to change the plan of your previous supply of water pipes.
Your tools and material list should comprise the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic due to the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the staying water that will originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place in between the faucet as well as the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap connectors. The former type needs to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wood boards under its feet, place the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub up until the level reviews degree.
To install taps, fit the bottom of the outermost flexible faucet adapter to the ideal supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bathtub and also check the overflow outlet and the typical outlet for leaks.
Finally, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been made use of at the very least when as this will resolve it right into its last placement.
Planning for the Setup
First of all, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the flexible tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, creating the water to penetrate the wall in between the bath and also the tiling, resulting in difficulties with dampness and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can fracture rather early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the market. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very involved in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you enjoyed the new page. I beg you set aside a second to promote this blog entry if you enjoyed reading it. I praise you for your time. Please come visit our site back soon.
Visit Website
Report this page